Vehicles
258 not categorized PORSCHE CAYENNE A CONTROL ARMCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.BBI9964010002 Finally, a complete solution to properly widen the front track width of a Porsche 996 and 997 turbo. To help increase front end grip, this kit allows full negative camber adjustment without binding the axles and fitment of wider wheel/tire combinations and GT3 cup car fenders. Each kit includes lower control arms, thrust arms, axle spacers, upper mounts, and camber shims.
$3,695.00
Make a selection BBI9974010001 Features
$1,895.00
Make a selection FVD34101702ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$418.00
Make a selection ER2290000 Diy kit - front control arm rubber bushings are now available as a kit for self-installation. in addition to a complete set of 4 OEM spec rubber bushings, the kit includes proprietary installation tools and instructions, which are essential for successful installation. use a pipe clamp or shop press to complete the install. General Fitment914 1970-76912 1965-69 911 1965-69 911 1970-73 911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89
$249.00
Make a selection FVD33150020 This kit is complete and includes the front and rear monoball cartridges with press tools. Our weather sealed monoball cartridges are crafted in high carbon steel and 7075 t6 aircraft aluminum. They will positively locate the suspension arms so suspension motion is accurately repeated in every corner. Sold as a set of 4. 1 kit is necessary per car. Please note: noise may resonate inside the cabin during street use.
$715.00
Make a selection FVD33150005 Restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm cannot compensate enough when lowering your Porsche, leaving you with as much as ½ inch of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration. Sold in pairs. 1 necessary per car.
$764.50
Make a selection ER2290002 Diy kit - rear 914 control arm rubber bushings are now available as a kit for self-installation. in addition to a complete set of 4 OEM spec rubber bushings, the kit includes proprietary installation tools and instructions, which are essential for successful installation plus the rear control arm shafts use a pipe clamp or shop press to complete the install. General Fitment914 1970-76911 1965-69 911 1970-73 911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89
$439.99
Make a selection FVD34101702AT By ordering this part number you get after previous sending in General Fitment911 1994-98
$417.56
Make a selection FVD34101802AT By ordering this part number you get after previous sending in General Fitment911 1994-98
$417.56
Make a selection FVD34101702RAK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrange...(choose a part on the right to read more)
$438.90
Make a selection FVD34101702RAT We will send you a reconditioned control arm, kindly send back your old part, or core . The reconditioned control arm has been full inspected, disassembled, degreased and we have properly installed FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner. Please note: each control arm is remanufactured in Germany, so the lead times can vary. This part is sold on an exchange basis, as such an additional charge (a core deposit) will be added to the purchase price of the part. After receiving your new part, kindly send back your old part, or core . Once the core is returned to us and it has been inspected to ensure it is rebuild-able and r...(choose a part on the right to read more)
$440.00
Make a selection FVD34101802RAT We will send you a reconditioned control arm, kindly send back your old part, or core . The reconditioned control arm has been full inspected, disassembled, degreased and we have properly installed FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner please note: each control arm is remanufactured in Germany, so the lead times can vary. This part is sold on an exchange basis, as such an additional charge (a core deposit) will be added to the purchase price of the part. After receiving your new part, kindly send back your old part, or core . Once the core is returned to us and it has been inspected to ensure it is rebuild-able and re...(choose a part on the right to read more)
$440.00
Make a selection FVD34102700ATK By ordering this part number you get after previous sending in your wishbone overhauled with new race-silent blocs back. The race-silent blocs (85 shore) give you more stable driving. Should it not be repairable, we will inform you immediately.
$279.40
Make a selection FVD341999R Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with our FVD clubsport series. They are made from rubber with a 85 shore hardness value which is the same as the rennsport models. 85 shore is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This is the ideal upgrade for street and light track / clubsport use. This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes 85 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$124.30
Make a selection FVD34102802AT By ordering this part number you get after previous sending in your wishbone overhauled with new race-silent blocs back. General Fitment968 1992-95944 1982-85 944 1985-88
$501.41
Make a selection FVD34105385 Querlenker FVD641330360 mit 85 shore sportbuchsen und lager. Sport lager mit 85 shore sind 40% harter gegenuber den originalen oem-lagern (65 shore). - perfekt fur sportlich-strasse und clubsport
$313.50
Make a selection FVD34105304BU1 Diese buchse ersetzt an ihrem vorderen querlenker die mittlere buchse. Es handelt sich bei dieser buchse um einen hartegrad von 85 shore wie original bei den rs -modellen ( GT3 rs, GT2 rs ) preis pro stuck, pro querlenker wird ein stuck benotigt.
$115.50
Make a selection FVD3419991 This is a cost effective alternative to buying new control arms. Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with new bushings of the same rubber (65 shore hardness value). This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes a 65 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$124.30
Make a selection FVD34391101SET Replace worn-out original front lower control arm bushings to return your car to its intended suspension geometry and steering feedback. Features: better handling reduces that sloppy steering feel does not produce any noise like the teflon bushings. Rubber has the original shore hardness value of 65 (like oem) fit's like oem, simple installation made in Germany if you are looking for a sportier upgrade we suggest our sport lower control arm set, part # FVD34391192set. Set is sold per axle. 2 necessary per car.
$152.90
Make a selection PT34916 Permatune has long been a favorite alternative to the outrageously priced Bosch electronic ignition control unit. Today’s perma-tune is all new on the inside, and bolts up and plugs in to the same location as the stock system. The units increase spark energy to three times that of the stock ignition system. This is why spark plugs will never foul again, even when set to large spark plug gaps and will actually recover from fuel contamination. This increase in spark energy allows your engine to make more power for the same amount of fuel. Meticulously assembled by fellow americans in texas, the permatune outperforms the Bosch unit and at a much lower price. Installation is a direct plug-in. Get the spark back i...(choose a part on the right to read more) General Fitment911 1978-83911 1984-86 911 1987-89
$896.07
Make a selection S701041 Rennline adjustable control arm links solve both these problems. Manufactured from 6061 aluminum and feature a turnbuckle design that allows each arm to be lengthened or shortened as needed to restore proper suspension geometry on a lowered Porsche. The fk teflon-lined rod end bearings ensure precision handling and lock in your car's alignment settings, ensuring predictable cornering under all conditions. Unlike the competitors' product, rennline arms come with eccentric locks and new hardware so you can completely eliminate the factory setup, which is known to go out of adjustment under hard driving and ruin your car's alignment. Note: two required per car. General Fitment911 1998-05911 TURBO/GT2 2001-05 911 GT3 2003-05 911 2005-08 911 GT3 2007-11 CAYMAN 2006-08 BOXSTER 2005-08
$306.90
Make a selection S715012 Rennline adjustable control arm links solve both these problems. Manufactured from 6061 aluminum and feature a turnbuckle design that allows each arm to be lengthened or shortened as needed to restore proper suspension geometry on a lowered Porsche. The fk teflon-lined rod end bearings ensure precision handling and lock in your car’s alignment settings, ensuring predictable cornering under all conditions. Note: four required per car. General Fitment911 1998-05911 TURBO/GT2 2001-05 911 GT3 2003-05 911 2005-08 911 GT3 2007-11
$236.50
Make a selection S727374101 If you're serious about how your 993 handles, you should upgrade the rear suspension with adjustable control arm links. There are two major drawbacks to the factory links: 1) you can't lower your car and maintain proper suspension geometry. The factory links create too much toe-in, which cannot be adjusted out, creating handling problems and excessive tire wear. 2) the factory links have rubber bushings, which make handling imprecise, especially in performance driving when suspension loads are highest. General Fitment911 1994-98
$1,758.90
Make a selection
$307.70
Make a selection S745012 Rennline adjustable control arm links solve both these problems. Manufactured from 6061 aluminum and feature a turnbuckle design that allows each arm to be lengthened or shortened as needed to restore proper suspension geometry on a lowered Porsche. The fk teflon-lined rod end bearings ensure precision handling and lock in your car's alignment settings, ensuring predictable cornering under all conditions. Unlike the competitors' product, rennline arms come with eccentric locks and new hardware so you can completely eliminate the factory setup, which is known to go out of adjustment under hard driving and ruin your car's alignment. Sold each, two needed per car. General Fitment911 1994-98
$306.90
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |